Linux/Device

PLANEX GW-USMicro300.jpg

Debian stretch testing amd64

$ sudo apt install firmware-misc-nonfree
$ dmesg
  :
[356038.786415] usb 2-1.1: USB disconnect, device number 25
[356043.916280] usb 2-1.1: new high-speed USB device number 26 using ehci-pci
[356044.028191] usb 2-1.1: New USB device found, idVendor=2019, idProduct=ab29
[356044.028195] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[356044.028197] usb 2-1.1: Product: GW-USMicro300
[356044.028199] usb 2-1.1: Manufacturer: PLANEX COMMUNICATIONS INC.
[356044.028200] usb 2-1.1: SerialNumber: 1.0
[356044.104214] usb 2-1.1: reset high-speed USB device number 26 using ehci-pci
[356044.205385] ieee80211 phy4: rt2x00_set_rt: Info - RT chipset 3071, rev 0213 detected
[356044.233629] ieee80211 phy4: rt2x00_set_rf: Info - RF chipset 0008 detected
[356044.234052] ieee80211 phy4: Selected rate control algorithm 'minstrel_ht'
[356045.332130] rt2800usb 2-1.1:1.0 wlx0022cfxxxxxx: renamed from wlan0
[356045.356331] IPv6: ADDRCONF(NETDEV_UP): wlx0022cfxxxxxx: link is not ready
[356045.356384] ieee80211 phy4: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[356045.356408] rt2800usb 2-1.1:1.0: firmware: direct-loading firmware rt2870.bin
[356045.356413] ieee80211 phy4: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[356045.636398] IPv6: ADDRCONF(NETDEV_UP): wlx0022cfxxxxxx: link is not ready
[356045.700496] IPv6: ADDRCONF(NETDEV_UP): wlx0022cfxxxxxx: link is not ready
$ lsusb
Bus 002 Device 025: ID 2019:ab29 PLANEX GW-USMicro300
$ /sbin/ifconfig wlx0022cfxxxxxx
wlx0022cfxxxxxx: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether 00:22:cf:xx:xx:xx  txqueuelen 1000  (イーサネット)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
$ /sbin/iwconfig wlx0022cfxxxxxx
wlx0022cfxxxxxx  IEEE 802.11bgn  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=20 dBm   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Power Management:off
$ sudo /sbin/iwconfig wlx0022cfxxxxxx mode master
Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlx0022cfxxxxxx ; Invalid argument.
$ sudo /sbin/iwconfig wlx0022cfxxxxxx mode ad-hoc
Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlx0022cfxxxxxx ; Device or resource busy.
$ sudo /sbin/iwconfig wlx0022cfxxxxxx mode managed

Rasbian jessie

$ dmesg
  :
[  121.336485] usb 1-1.5: new high-speed USB device number 5 using dwc_otg
[  121.456750] usb 1-1.5: New USB device found, idVendor=2019, idProduct=ab29
[  121.456776] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  121.456793] usb 1-1.5: Product: GW-USMicro300
[  121.456809] usb 1-1.5: Manufacturer: PLANEX COMMUNICATIONS INC.
[  121.456824] usb 1-1.5: SerialNumber: 1.0
[  122.706487] usb 1-1.5: reset high-speed USB device number 5 using dwc_otg
[  122.815705] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3071, rev 0213 detected
[  122.841709] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
[  122.860639] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[  122.862373] usbcore: registered new interface driver rt2800usb
[  122.927066] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2870.bin'
[  123.043656] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.29
[  123.424740] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[  125.589509] wlan0: authenticate with 12:6f:3f:07:9f:ce
[  125.692336] wlan0: send auth to 12:6f:3f:07:9f:ce (try 1/3)
[  125.694390] wlan0: authenticated
[  125.695212] rt2800usb 1-1.5:1.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[  125.696530] wlan0: associate with 12:6f:3f:07:9f:ce (try 1/3)
[  125.699372] wlan0: RX AssocResp from 12:6f:3f:07:9f:ce (capab=0x411 status=0 aid=1)
[  125.705302] wlan0: associated
[  125.705347] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
$ lsmod |grep rt
rt2800usb              17716  0 
rt2800lib              71860  1 rt2800usb
rt2x00usb               8545  1 rt2800usb
rt2x00lib              36833  3 rt2x00usb,rt2800lib,rt2800usb
mac80211              518846  3 rt2x00lib,rt2x00usb,rt2800lib
crc_ccitt               1161  1 rt2800lib
cfg80211              399468  2 mac80211,rt2x00lib
$ dpkg -L raspberrypi-bootloader | grep rt28
/lib/modules/4.1.17+/kernel/drivers/net/wireless/rt2x00/rt2800lib.ko
/lib/modules/4.1.17+/kernel/drivers/net/wireless/rt2x00/rt2800usb.ko
/lib/modules/4.1.17-v7+/kernel/drivers/net/wireless/rt2x00/rt2800lib.ko
/lib/modules/4.1.17-v7+/kernel/drivers/net/wireless/rt2x00/rt2800usb.ko
$ apt-get download firmware-misc-nonfree
$ ar x firmware-misc-nonfree_20160110-1_all.deb
$ tar xf data.tar.xz
$ tar tvf data.tar.xz |grep rt2870.bin
-rw-r--r-- root/root      8192 2016-01-11 06:36 ./lib/firmware/rt2870.bin
lrwxrwxrwx root/root         0 2016-01-11 06:36 ./lib/firmware/rt3070.bin -> rt2870.bin
$ sudo iwconfig wlan0 mode master
Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlan0 ; Invalid argument.
$ sudo iwconfig wlan0 mode ad-hoc
Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlan0 ; Device or resource busy.
$ sudo iwconfig wlan0 mode managed

alpine 3.3.1 i686

[577467.192432] usb 2-1: USB disconnect, device number 2
[577470.958993] usb 1-1: new high-speed USB device number 5 using ehci-pci
[577471.102710] usb 1-1: New USB device found, idVendor=2019, idProduct=ab29
[577471.102722] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[577471.102730] usb 1-1: Product: GW-USMicro300
[577471.102738] usb 1-1: Manufacturer: PLANEX COMMUNICATIONS INC.
[577471.102746] usb 1-1: SerialNumber: 1.0
[577471.113819] Thunar[2411]: segfault at 54e9b2dc ip 55eae57b sp 5f35d190 error 4 in ld-musl-i386.so.1[55e63000+81000]
[577471.113871] grsec: Segmentation fault occurred at 54e9b2dc in /usr/bin/thunar[Thunar:2411] uid/euid:1001/1001 gid/egid:1001/1001, parent /bin/busybox[init:1] uid/euid:0/0 gid/egid:0/0
[577471.113967] grsec: denied resource overstep by requesting 4096 for RLIMIT_CORE against limit 0 for /usr/bin/thunar[Thunar:2411] uid/euid:1001/1001 gid/egid:1001/1001, parent /bin/busybox[init:1] uid/euid:0/0 gid/egid:0/0
[577471.572313] usb 1-1: reset high-speed USB device number 5 using ehci-pci
[577471.705205] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 3071, rev 0213 detected
[577471.733577] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 0008 detected
[577471.734548] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[577471.737597] usbcore: registered new interface driver rt2800usb

参考URL



spam 避けですcheck を付けて下さい

添付ファイル: filePLANEX GW-USMicro300.jpg 77件 [詳細]

トップ   編集 凍結 差分 バックアップ 添付 複製 名前変更 リロード   新規 一覧 単語検索 最終更新   ヘルプ   最終更新のRSS
Last-modified: 2016-03-06 (日) 10:42:30 (317d)